It's also not required you order the CE marking at the same time as you order your boat kit. The price for CE marking is € 295.Īs said before there is not required you get your new boat CE marked when building it from one of our boat kits. Second you will have to ask us to do the necessary arrangements, so we can CE mark your new boat. The first requirement is that you follow the building instruction and don't make changes when constructing your new boat. For various reasons you can choose to get your finished boat CE marked and we can assist you in this process. Here we try to guide you with a short explanation.Īs basis a boat you build from our boat kits shall not be CE marked as long as you build them for yourself and don't want to sell it within 5 years after finishing it. The CE marking rules for boat kits are not simple to understand. The boat kits labeled with CE can be CE marked. Therefore not all our boat kits can be CE marked. The boat kits complete package contain the following:įiberglass fabric for gluing the long bottom and side panelsĮpoxy resin to glue the plywood, fiberglass tape and fabricĪccording to the CE marking rules canoes, kayaks and boats under 2,5 meter length can't be CE marked. The building instruction describes the use of epoxy and filler in details. The filler is used to thicken the epoxy so you can use it between the hull panels and frames. The package also contains filler for the epoxy. However if you end up needing more epoxy you will be able to order more.
#Diy kite boat plus
However we know the amount can vary from builder to builder so we have tried to match an average plus a bit extra. The amount is carefully weight out and is enough to glue the panels, fiberglass tape, fiberglass fabric and to prime the boat before painting.Įpoxy is expensive so the amount will be what you need. The package also contain the amount of epoxy necessary to build you new boat. The building instructions explain the process in details. You must cut this fiberglass fabric in suitable sizes yourself and the tape must also be cut in the right lengths. At the same time the package contain fiberglass fabric so you can glue the bottom and side panels. Our fiberglass package has the right amount of tape to build the boat in questions. The width of the fiberglass tape depends on the boat kit you choose. The package contain all necessary fiberglass and fabric together with epoxy, hardener and fillers. To make it as easy for you as possible to build your new boat we have made this complete package. The boat kits basis package consist of the following:
#Diy kite boat manuals
The drawings, building instruction and manuals are in English language. The technique is really suitable for home boat builders and gives you a strong and lightweight hull. The building process is stitch and glue which means that you will start with stitching the parts with wire or cable ties and then afterwards glue with epoxy and fiberglass. The manuals consists of more than 100 pages of instruction that will guide you through the building process. To make the boat building as easy for you as possible we have made 5 building manuals. When you pint yourself it also has the advantage that you can print new copies should the first ones be damaged during your work. They can be printed on an ordinary standard A4 printer. You will receive these documents by email and you will have to print them yourself. With the plywood parts you will also receive drawings, building instructions and building manuals. If you have any special requests for the plywood you are most welcome to contact us, since we can deliver the boat kit with any plywood you want. The plywood is fine for boats that will be painted, but since the colour can vary we can't guarantee you will be able to varnish the boat. The plywood from far east are typically made from Bintangor. We use plywood from the far east or plywood from pine. You don't even have to sand the edges of the plywood parts with sandpaper before you begin. All you have to do is unpack the parts before you can start building your new boat. This means that the plywood parts are cut with hundredth of millimeters accuracy.Įvery single plywood part are cut and labeled.
#Diy kite boat software
The plywood parts are cut at our factory where we have the most modern CAM software and CNC milling machines. Beside this basic package you will need some fiberglass and epoxy (please see further down the page for more details about this). Our boat kit consist of a basic package with all the plywood parts to build the boat is included.
0 kommentar(er)
